Background Image

DOCUMENTATION

?

Shortcut

PrevPrev Article

NextNext Article

Larger Font Smaller Font Up Down Go comment Print

Introduction: This guide describes how to configure the volume and memory of CUBRID for live services, and how to configure CUBRID according to the number of concurrent users.

 

Applicable system: CUBRID 10.2

 

DB Creation and Volume Configuration

If an operator creates a DB using the createdb utility after setting up CUBRID without options, a DB with a size of 512 MB will be created by default. While a DB of this size is fine for testing and development purposes, it is not optimal for live services.

To accommodate the data generated by live services, use the addvoldb utility to add more volume to a DB. If possible, create each volume on a physically separate drive. Distributing I/O increases performance.

The following is an example of configuring a DB so that it will have 10 GB allocated to the permanent volume, 256 MB to the active log and 2 GB to the temp volume. In this example, the data volumes are in the same partition, while the active log and temp volume shares another partition to distribute I/O.

 

cubrid createdb -F /db/boarddb/data –L /db/boarddb/log --log-volume-size=256M --db-volume-size=5G boarddb
cubrid addvoldb -S -p data -F /db/boarddb/data --db-volume-size=5G boarddb
cubrid addvoldb -S -p temp -F /db/boarddb/log --db-volume-size=2G boarddb

 

Configuration Modification

Some parameters in the configuration file should be modified according to system specifications and the number of concurrent users. For more information on the parameters described below, see the Manual > CUBRID Management > System Parameters > Configuring the Database Server and Broker Configuration sections, respectively.

 

https://www.cubrid.org/manual/en/10.2/admin/config.html

 

Parameters Related to the Number of Concurrent Users

Modify the value of max_clients in cubrid.conf and MAX_NUM_APPL_SERVER (the number of maximum CAS processes) in cubrid_broker.conf to configure the number of concurrent users.

The value of MAX in the WAS connection pool and the system memory specification affect this configuration.

First, configure the value of MAX in the WAS connection pool and the value of MAX_NUM_APPL_SERVER in cubrid_broker.conf so that the two values are the same. For example, the value above must be identical to the value configured in maxActive in Tomcat. Configure this value in consideration of system memory.

The maximum amount of memory that a single CAS process uses is 80 MB in the 64-bit Windows version by default. For example, if the value of MAX_NUM_APPL_SERVER is 100 in the 64-bit Windows version of CUBRID, up to 8 GB of system memory can be used.

Modify the following in $CUBRID/conf/cubrid_broker.conf:

[%query_editor]
MAX_NUM_APPL_SERVER     =20 

[%BROKER1]
MAX_NUM_APPL_SERVER     =80 

Next, modify max_clients according to the value of MAX_NUM_APPL_SERVER.

The value of max_clients should be a number that equal to the sum of all the values of MAX_NUM_APPL_SERVER, added by 10.

Modify the parameter of $CUBRID/conf/cubrid.conf as shown below:

max_clients=110

 

Parameters Related to Memory and Disks

Modify and add the parameters of $CUBRID/conf/cubrid.conf that are related to memory and disks, as shown below:

data_buffer_size=2G
sort_buffer_size=2M
temp_file_memory_size_in_pages=20 #add this parameter
temp_file_max_size_in_pages=250000 #add this parameter

It is recommended to configure the value of the data_buffer_size so that it does not exceed two-thirds of the total system memory. If the value of data_buffer_size 2G, as in the example above, 2 GB of memory will be used. Modify this value so that it is appropriate for the broker memory usage.

temp_file_max_size_in_pages is a parameter that specifies the maximum number of pages that can be allocated to save to the temp volume on a disk. This parameter is necessary to prevent a bad query from causing a service failure by creating temp volumes infinitely until the disk becomes full. In the example above, it is set to use up to 4 GB (250,000 * 16K (the default value of db page size) of free space.


  1. Introduction to CUBRID Security – Part II

    Date2020.06.26 CategoryServer
    Read More
  2. Introduction to CUBRID Security – Part I

    Date2020.06.25 CategoryServer
    Read More
  3. CUBRID Configuration Guide to Launch Services

    Date2020.06.24 CategoryServer
    Read More
  4. CUBRID Java Stored Procedures

    Date2020.06.24 CategoryServer
    Read More
  5. CUBRID Port and iptables (firewall) Configuration

    Date2020.06.24 CategoryServer
    Read More
  6. CUBRID Backup & Restore – Part II (Restore)

    Date2020.06.22 CategoryServer
    Read More
  7. CUBRID Backup & Restore – Part I (Backup)

    Date2020.06.22 CategoryServer
    Read More
  8. Common Uses of CUBRID Node.js API with Examples

    Date2020.06.10 CategoryInterfaces
    Read More
  9. CUBRID Triggers

    Date2020.06.10 CategoryServer
    Read More
  10. CUBRID Log Files

    Date2020.06.10 CategoryServer
    Read More
Board Pagination Prev 1 2 Next
/ 2

Join the CUBRID Project on